maruwa g eneral catalog emi filters 90
item dissipation factor withstanding voltage insulation resistance adhesion strength of termination solderability no more than 5% or 0.5pf, whichever is larger. within 12.5% within 30% less than 4% 1) less than 7.5% 1) no mechanical damage no less than 10,000m or 500m ? f, whichever is smaller. performance unit : mm 45 2 45 2 10 20 r=230 vibration resistance visual capacitance dissipation factor resistance to soldering heat visual capacitance dissipation factor insulation resistance withstanding voltage temperature cycling visual capacitance dissipation factor insulation resistance withstanding voltage humidity load test visual capacitance dissipation factor insulation resistance life test at high temperature load dissipation factor insulation resistance visual capacitance flexion visual capacitance no more than 3% or 0.3pf, whichever is larger within 12.5% within 30% no remarkable damage no less than 10,000m or 500m ? f, whichever is smaller. less than 5% 1) less than 7.5% 1) no more than 5% or 0.5pf, whichever is larger. within 12.5% within 30% no remarkable damage initial standard values must be satisfied. initial standard values must be satisfied . no damage or insulation breakdown. no more than 2.5% or 0.25pf, whichever is larger. within 7.5% within 20% no remarkable damage termination surface should be covered with new solder to over 75%. initial standard values be satisfied. initial standard values be satisfied. no damage or insulation breakdown. no remarkable damage within specified tolerance initial standard values must be satisfied. no more than 2.5% or 0.25pf, whichever is larger. within 7.5% within 20% no remarkable damage chip 5n substrate no peeling-off or exfoliation shall be manifest or recognizable in its incipient stages. no less than 10,000m or 500m ? f, whichever is smaller. no insulation breakdown and no failure. 2.5% or less 1) 5% or less 1) r cg, uj f testing method and conditions (in accordance with jis c5101-1) rated voltage is applied for 1 minute. cg : 1mhz uj, r, f : 1khz measurement voltage : 0.5~2vrms application time is 1~5seconds. cg, uj : 300% of rated voltage r, f : 250% of rated voltage solder a specimen on the testing jig shown on the left and apply a force of 5n (0.51kgf) in the direction indicated by arrow. vibration frequency : 10~55hz full amplitude : 1.5mm, 10~55~10hz 1min. xyz direction 2hrs for each total 6hrs. solder : h60a or h63a (jis z 3282) soldering temperature : 270 5 c immersion time : 10 1sec. preheat : 80 ~ 100 c (1~2min.) and 170 ~ 200 c (1~min.) immersion into solder should be carried out continuously after preheating. solder : h60a or h63 (jis z 3282a) soldering temperature : 230 5 c immersion time : 2 1sec. step temperature time 1 lower limit temp. 30min. 2r oom temp. 3min. 3u pper limit temp. 30min. 4r oom temp. 3min. these four temperatures in the above order completes one cycle. the cycle is repeated 25 times. test temp : 40 2 c relative humidity : 90~95% testing time : 1000 +48, ? 100% of rated voltage is applied test temp : upper limit temp. 3 c testing time : 1000 +48, ? 200% of rated voltage is applied. 2) add load at a speed of about 1mm per second until flexion amount reaches 1mm and keep the condition for 5 minutes. have a capacitance meter connected to both ends of sample during a test. 16v r type name temperature characteristics rated voltage initial moistureproof load high-temperature load 7.5% max. 12.5% max. 5% max. 9% max. 7% max. 6.3v *1) dielectric dissipation factor *2) the following products are applied voltage 150%. cnh20r224m m cnh20r474m m cnh20r105m m the following product is applied rated voltage c nh20r475m m c nh20r106m m c nh10r105m m cnh20r224m m cnh20r474m m cnh20r105m m cnh20r475m m cnh20r106m m cnh10r105m m 12.5% max.
|
